rs5-r30/rd30 3.0 watt 2:1 regulated single & dual output 8 pin sip8 package wide 2:1 input range 1600 vdc isolation continuous short circuit protection efficiency up to 84% -40c~71c operation temperature range metal case, remote on/off optional page: 1/4 last update: 30.01.09 output specifications absolute maximum ratings (4) 1) ripple / noise measured with 20 mhz bandwith. 2) tested by minimal vin and constant resistive load. 3) measured input reflected ripple current with a simulated source inductance of 12uh and source capacitor cin (47uf, esr < 1.0 ohm @100 khz). 4) exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5) operation at no-load conditions will not damage these devices. however they may not meet all listed specifications. transient recovery time 300 us typ., transient response deviation 3% max., test by normal vin and 100% - 25% load, 25% load step change. remote on / off control on: open or high impedance off: 3.0~6.0 ma input current (via 1k) input filter components are required to help meet conducted emission class a, which application refer to the emi filter of design & feature configuration. an external filter capacitor is required if the module has to meet en61000- 4-4 and en61000-4-5. voltage accuracy 1% line regulation 0.5% load regulation (from 25% to 100% load) 1% cross regulation (dual output) 5% ripple & noise (20 mhz bandwith) (1) 75 mv pk-pk short circuit protection indefinite (automatic recovery) temperature coefficient 0.02%/c capacitor load (2) see table voltage range see table max. input current see table no-load input current see table input filter capacitors input reflected ripple current (3) 35 ma pk-pk input specifications efficiency see table i/o isolation voltage (3 sec.) input / output 1600 vdc i/o isolation capacitance 680 pf max. i/o isolation resistance (min.) 1000 m ohm switching frequency (min.) 100 khz humidity 95% rel. h reliability calculated mtbf > 2.465 mhrs. @25c safety standard (designed to meet) iec 60950 general specifications case material non-conductive black plastic pin material c5191r-h solder-coated potting material epoxy (ul94v-0 rated) weight 4.8 g, typ. dimensions sip > 0.86 x 0.36 x 0.44 physical specifications operating temperature -40c~ 71c maximum case temperature 100c storage temperature -40c~125c cooling nature convection environment specifications note these are stress ratings. exposure of devices to any of these conditions may adversely affect long-term reliability. input voltage (100 ms) 5 modes -0.7 ~ 15 vdc 12 modes -0.7 ~ 36 vdc 24 modes -0.7 ~ 50 vdc 48 modes (sip) -0.7 ~ 100 vdc lead soldering temperature 260c (1.5 mm from case 10 sec.) all specifications typical at ta = 25c, nominal input voltage and full load unless otherwise specified. the information and specifications contained in this data sheet are believed to be correct at time of publication. however, we accept no responsibility for consequences arising from printing errors or inaccuracies. subject to change without notice. conducted emissions (10) en55022 class a radiated emissions en55022 class a esd iec61000-4-2 perf.criteria b rs iec61000-4-3 perf.criteria a eft (11) iec61000-4-4 perf.criteria b surge (11) iec61000-4-5 perf.criteria b cs iec61000-4-6 perf.criteria a pfmf iec61000-4-8 perf.criteria a emi characteristics
rs5-r30/rd30 3.0 watt 2:1 regulated single & dual output model selection guide page: 2/4 last update: 30.01.09 number structure isolation 1=1.6 kvdc power 30=3.0w output 03=3.3v 05=5v 12=12v 15=15v code internal type r=single regulated rd=dual regulated input 05=4.5-9v 12=9-18v 24=18-36v 48=36-72v name/package rs5=sil8 rs5 - xx xx r/rd 30 a x** model number input input current (ma) output output current efficiency capacitor range vdc no load / full load vdc full load (ma) @fl (%) load ( hf) rs5-0503r30a1 4.5-9 65 / 640 3.3 700 74 2200 rs5-0505r30a1 4.5-9 70 / 800 5 600 76 1000 rs5-0512r30a1 4.5-9 75 / 750 12 250 82 470 rs5-0515r30a1 4.5-9 75 / 750 15 200 82 220 rs5-1203r30a1 9-18 25 / 260 3.3 700 76 2200 rs5-1205r30a1 9-18 15 / 320 5 600 81 1000 rs5-1212r30a1 9-18 35 / 305 12 250 84 470 rs5-1215r30a1 9-18 35 / 305 15 200 84 220 rs5-2403r30a1 18-36 15 / 133 3.3 700 74 2200 rs5-2405r30a1 18-36 15 / 160 5 600 79 1000 rs5-2412r30a1 18-36 20 / 156 12 250 82 470 rs5-2415r30a1 18-36 20 / 152 15 200 84 220 rs5-4803r30a1 36-72 10 / 66 3.3 700 75 2200 rs5-4805r30a1 36-72 10 / 82 5 600 78 1000 rs5-4812r30a1 36-72 15 / 78 12 250 81 470 rs5-4815r30a1 36-72 15 / 78 15 200 81 220 rs5-0505rd30a1 4.5-9 90 / 800 5 300 77 470 rs5-0512rd30a1 4.5-9 90 / 760 12 125 81 220 rs5-0515rd30a1 4.5-9 90 / 750 15 100 82 100 rs5-1205rd30a1 9-18 45 / 320 5 300 80 470 rs5-1212rd30a1 9-18 45 / 308 12 125 83 220 RS5-1215RD30A1 9-18 45 / 312 15 100 82 100 rs5-2405rd30a1 18-36 20 / 160 5 300 80 470 rs5-2412rd30a1 18-36 20 / 154 12 125 83 220 rs5-2415rd30a1 18-36 20 / 154 15 100 83 100 rs5-4805rd30a1 36-72 15 / 82 5 300 78 470 rs5-4812rd30a1 36-72 20 / 80 12 125 80 220 rs5-4815rd30a1 36-72 15 / 78 15 100 81 100 derating curve options: please add suffix ?m for metal case. please add suffix ?c for remote control function.
input reflected ripple current test step input reflected ripple current is measured through a source inductor lin (12 uh) and a source capacitor cin (47 uf, esr < 1.0 m at 100 khz) at nominal input and full load. output ripple & noise measurement test the scope measurement bandwidth is 20 mhz. efficiency vs output current 05 05 models efficiency vs output current 12 12 models efficiency vs output current 24 24 models test configurations emi filter input filter components (c1, l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. page: 3/4 last update: 30.01.09 efficiency vs output current 48 48 models rs5-05xxxxx rs5-12xxxxx rs5-24xxxxx rs5-48xxxxx the models listed are just for standard type. if you need a special specification product, please contact our service. phone: +49 69 984047-0, mail to: info@rsg-electronic.de or use the forms on www.rsg-electronic.de (?kontakt). rs5-r30/rd30 3.0 watt 2:1 regulated single & dual output
mechanical specifications page: 4/4 last update: 30.01.09 mail: info@rsg-electronic.de www.rsg-electronic.de rsg electronic components gmbh sprendlinger landstr. 115 d-63069 offenbach tel. +49 69 984047-0 fax +49 69 984047-77 rsg rs5-xxxxx30a1 8 pin sil package non-conductive plastic rs5-r30/rd30 3.0 watt 2:1 regulated single & dual output 8 pin sil package nickel coated copper mechanical specifications all dimensions are typical in millimeters (inches). 1) pin diameter: 1.0 0.05 (0.04 0.002) 2) pin pitch tolerance: 0.35 ( 0.014) 3) case tolerance: 0.5 ( 0.02) rsg rs5-xxxxx30a1 pin number 1 2 3 5 6 7 8 dual +c -v input +v input remote on/off n.c. +v output common -v output single +c -v input +v input remote on/off n.c. +v output -v output n.c. pin connections +c models pin number 1 2 3 5 6 7 8 dual -v input +v input n.c. n.c. +v output common -v output single -v input +v input n.p. n.p. +v output -v output n.c. pin connections
|
